Distillation Lab Report

Data and Conclusions: The purpose of this experiment was to learn how to use distillation and gas chromatography to separate and identify different compounds from a given mixture. There are several kinds of distillation methods. However, the method that we used in this experiment was fractional distillation. This method is used when trying to separate two different volatile compounds whose boiling points differ by 40-50°C or more.
If the boiling points are too close, this method will not work because the two compounds will begin evaporating at close temperatures and will condense down to the receiving flasks at relatively the same times. This will not create an ideal separation. The apparatus used for this type of distillation is longer than that of a simple distillation experiment because this kind of apparatus creates more efficient separation. This happens because the fractional distillation apparatus is longer, and allows for several simple distillations to occur within the column itself to more accurately separate liquids.
The inside of the column is said to have theoretical plates, or equilibrium stages that are created by the vapor and liquid stages of a compound that create this accuracy. The column must also be insulated with cotton and aluminum to prevent any heat loss that may lead to inaccurate temperature readings or even effect the evaporation of the different compounds. When heating the stillpot, flameless heating should be used along with a magnetic stirbar. This is important to control the temperature of the mixture and keep the heat smooth and constant.

Heating the mixture too fast could result in no fractionation in the column and lead to no separation. Likewise, if the mixture is heated too slowly, the vapors might now make it all the way to the condenser, and the liquid will fall back into the stillpot. If the mixture is heated correctly and constantly, the vapors should condense through a condenser and into a receiving flask. This condenser should have water running through it at all times to keep it cool and keep the condensed vapor flowing down into the receiving flask.
As a whole, the entire apparatus works perfectly for two different volatile liquids with 40-50°C boiling point differences because as the liquid with the lower boiling point is distilled out, the higher boiling point liquid will remain in the stillpot as the other is evaporating and distilled. Then, it will be able to evaporate later as the temperature rises, after the other has more than completely distilled out. As I conducted this portion of the experiment, I noticed that while taking the three fractions, fraction A filled up the full 15 mL and continued distilling through fraction B, and eventually stopped.
Because of this, I hypothesized that all of fraction A and most of fraction B consisted of the low boiling point compound. As I raised the temperature of the hotplate, I was able to collect fraction C, and I predicted that it was composed of mostly the high boiling point liquid. To test this, the experiment called for the use of gas chromatography. The chromatography would not only show the relative concentrations of each compound in the fraction, but could also help confirm the identification of the compounds we thought were in the fractions based on the temperatures that each liquid boiled.
Before trying to guess the correct compounds of the mixture, one must run each individual fraction through the machine to clearly see the composition of each. Gas chromatography works because as the liquid runs through the machine, its different components run through and exit at different times due to changes of temperatures that measure high and low boiling points. The machine records these using peaks of retention time that identify these different components. After obtaining this data, there was enough information to choose a reasonable match for each of the components.
Once both the fractions and the guessed compound were mixed, the retention recordings should not differ in the number of peaks because ideally the compound mixed should have the same retention time as one of the other previous peaks. If the compounds were to differ in the number of peaks, then it shows that another compound must be present with different properties. As I conducted this portion of the experiment, I guessed cyclohexane for my low boiling point liquid and toluene or heptane for my high boiling point liquid based on the fractional distillation observations.
For cyclohexane I mixed it with fraction A, since it predominantly consisted of my low boiling point liquid, and observed two peaks in my results. Therefore I concluded that cyclohexane was the low boiling point liquid. However, for the second liquid I guessed heptane first, and my results showed three peaks. Knowing that I had guessed wrong, I tested toluene mixed with my fraction C and only got two peaks. The high boiling point liquid proved to be toluene. In conclusion, my results all matched the main ideas and theories presented in the experiment.
From my results I was able to figure out the composition of each of the compounds in the initial mixture and compare them to those of the rest of the class. My results only varied by 3. 18%. When using the two different methods of calculating the composition, the second method using the chromatography peaks was more accurate, and compared to the first method of assuming the ideal compositions, the results differed from the class average by over 10%. Based on the consistency of our class results using the second method, the two compounds proved to have been distilled using the proper method, and is reinforced by the use of gas chromatography.

Don't use plagiarized sources. Get Your Custom Essay on
Distillation Lab Report
Just from $13/Page
Order Essay
Place your order
(550 words)

Approximate price: $22

Calculate the price of your order

550 words
We'll send you the first draft for approval by September 11, 2018 at 10:52 AM
Total price:
The price is based on these factors:
Academic level
Number of pages
Basic features
  • Free title page and bibliography
  • Unlimited revisions
  • Plagiarism-free guarantee
  • Money-back guarantee
  • 24/7 support
On-demand options
  • Writer’s samples
  • Part-by-part delivery
  • Overnight delivery
  • Copies of used sources
  • Expert Proofreading
Paper format
  • 275 words per page
  • 12 pt Arial/Times New Roman
  • Double line spacing
  • Any citation style (APA, MLA, Chicago/Turabian, Harvard)

Our guarantees

Delivering a high-quality product at a reasonable price is not enough anymore.
That’s why we have developed 5 beneficial guarantees that will make your experience with our service enjoyable, easy, and safe.

Money-back guarantee

You have to be 100% sure of the quality of your product to give a money-back guarantee. This describes us perfectly. Make sure that this guarantee is totally transparent.

Read more

Zero-plagiarism guarantee

Each paper is composed from scratch, according to your instructions. It is then checked by our plagiarism-detection software. There is no gap where plagiarism could squeeze in.

Read more

Free-revision policy

Thanks to our free revisions, there is no way for you to be unsatisfied. We will work on your paper until you are completely happy with the result.

Read more

Privacy policy

Your email is safe, as we store it according to international data protection rules. Your bank details are secure, as we use only reliable payment systems.

Read more

Fair-cooperation guarantee

By sending us your money, you buy the service we provide. Check out our terms and conditions if you prefer business talks to be laid out in official language.

Read more
Live Chat 1 763 309 4299EmailWhatsApp

Order your essay today and save 15% with the discount code GINGER